Announcement

Collapse

HUG - here for all audio enthusiasts

INTRODUCTION- PLEASE READ FIRST TO UNDERSTAND THIS FORUM!

"This Harbeth User Group (HUG) is the Manufacturer's own managed forum dedicated to natural sound, realisable by controlling the confounding variables between tthe microphone and the listeners' ears.

For example, the design of and interaction between the hifi amplifier and its speaker load can and potentially will alter the sound balance of what you hear. To reproduce the sounds captured by the recording microphones, as Harbeth speakers are designed to do, you would naturally select system components (sources, electronics, cables and so on) that do not color the sound before it reaches the speakers.

Identifying components for their system neutrality should, logically, start with the interpretation and analysis of their technical, objective performance, as any and every deviation from a measurably flat frequency response at any point along the serial chain from microphone to ear is very likely to cause the total system to have an audible sonic personality. That includes the contribution of the listening room itself.

HUG specialises in making complex technical matters simple to understand, aiding the identification of audio components likely to maintain a faithful relationship between the recorded sound and the sound you hear. With our heritage of natural sound, HUG cannot be really be expected to guide in the selection, approval, endorsement or even discussion of equipment that is intend to introduce a significantly personalised sound to the audio signal chain. For that you should do your own research and above all, make the effort to visit an Authorised Dealer and listen to your music at your loudness on your loudspeakers through the various electronics offered there. There is no on-line substitute for that time investment in a dealer's showroom.

If you desire to intentionally tune your system sound to your personal taste, please consider carefully how much you should rely upon the subjective opinions of strangers. Their hearing acuity and taste will be different to yours, as will be their motives and budget, their listening distance, listening loudness and listening room treatment, not necessarily leading to appropriate equipment selection and listening satisfaction for you.

Alternatively, if faithfully reproducing the sound intended by the composer, score, conductor and musicians over your speakers is your audio dream, then understanding something of the issues likely to fulfill that objective is what this forum has been helping with since 2006. Welcome!"


Jan. 2018
See more
See less

What coupling (if any) do i use in between my SHL5's and Sound Anchor stand? Blu Dots are awful!

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • What coupling (if any) do i use in between my SHL5's and Sound Anchor stand? Blu Dots are awful!

    Due to my ignorance I had been using the "Blu Dot" pads that Sound Anchor provides but they, to my dismay, made awful (and permanent) rings on the cabinets and have too much glue...when i took the speakers off the stands one Blue Dot actually ripped a small piece of the veneer right off! I had to pry the speakers off the stands.

    Any suggestions?? Thanks.

    Best,
    Noel

  • #2
    \stand-speaker isolation

    Hey, Noel

    I'd definitely use something.

    The stands I use under my Compact 7 ES-2's have small upward facing spikes, which contact the bottoms of the speakers (and yes, they leave small marks on the underside-not a problem for me). Under my Monitor 30's are Foundation stands, which use four small self-adhesive rubber pads at each corner. I'm a big believer in de-coupling the Harbeths from the stands in order to allow the thin wall cabinets to "breathe" on the undersides of the cabinet as well as the sides and tops. These self-adhesive rubber discs can be found at Lowes, Home Depot, etc.-they're typically used on the bottoms of chair legs and the like.

    Hope this is helpful, it's a cheap experiment to be sure.

    Comment


    • #3
      White-tak

      I use 3 very small pea sized bits of blue tack. Acutally its not blue but white made by Elmer. Noel of Skylan suggests that when you use any tack like material that you twist the speaker a bit when removing it to avoid it tearing the veneer.

      An option to using sticky stuff would be to purchase little neoprene bumpers you can get at hardware store that are used to provide a cushion to kitchen cabnet doors.

      Comment


      • #4
        Bumpons stand isolators

        Hi Noel,

        You could use large Polyurethane Bumpons,(3M) on your stands and these will add nice friction and help to dampen the contact of the cabinet to the hard steel,(place the bumpons on the stand top surface). Also there is quite a few folks that are happy using Herbies Big Fat Dots on their steel stands, http://herbiesaudiolab.net/ and you can give them a tryout for around 30 days and if they don't suit you can return them.

        Cheers,
        Noel.

        Comment


        • #5
          Spikes

          Hi Noel,

          Spike. I used blue-tac previously, but now my Compact 7 sits on spike.
          It will leave a mark underneath, but you'll soon forget about the mark coz it sounds wonderful

          Best regards

          Comment


          • #6
            BluTak or similar - not recommended

            As we say here in the Basic Guide, Item 12, BluTack or similar is not recommended. Over a period it will bond to the veneer and will rip it when attempting to remove the speaker from the stand. This is not covered by the Warranty! You have been warned (again)!

            During development we do not use any isolating agent. Alan just plonks the speakers on the stands so that he can swing them laterally to make masurements and do his listening.
            Harbeth PR,
            Harbeth UK

            Comment


            • #7
              M401 BluTak sandwich

              i use for my m40.1 the following sandwich: skylan stand -> blu tack -> small pieces of anti-rubber foil -> speaker.
              it works fine and the speakers do not have any contact with the blu tak.

              best
              Harbeth M40.1-Naim NAC52-Supercap-NAP 135-CDS2-XPS

              Comment


              • #8
                BluTak sandwich again

                You can use Blue Tac and not worry about pulling off vaneer by placing a paper mailing label on the bottom of the speaker where it will come in contact with the veneer.

                Comment


                • #9
                  Stand concepts and energy coupling

                  Some stands are designed to dissipate energy quickly without storing it. For these stands you need to couple the speaker to it rather than decouple. Suck it and see, as always.

                  Comment


                  • #10
                    Isolation pads

                    I know this reply is coming many months after the original post, but I'll give it a shot anyway - I use isolation pads from the German brand SSC (String Suspension Concept, www.hifi-ssc.de). They operate like isolation cones - you place them on the stand and the speaker rests on the felt pads that are on their upper surfaces so there's no chance of any damage to the veneer.

                    Comment

                    Working...
                    X